Quantcast
Channel: otira miniatures
Browsing latest articles
Browse All 25 View Live

Image may be NSFW.
Clik here to view.

rolling chassie

hi all, have assembled the rolling chassie. was most tricky with the small pins, they were 0.8mm diameter and were rivited.

View Article


Image may be NSFW.
Clik here to view.

redesign

hi all, well after some thought i decided to re-design. I can say that the current design can lead to a working model. I felt however that the design must be so the kit goes together with ease. i...

View Article


Image may be NSFW.
Clik here to view.

Article 22

hi all, have built the improved chassis. It goes together with far less effort. I had an idea to use pc board as the cover underneath as i can use it to attact the pick-ups.regards

View Article

Image may be NSFW.
Clik here to view.

further drawings

hi all, i have started to work on the boiler design. Shown is the overall dimensions. I will add the finer details as i go along.

View Article

Image may be NSFW.
Clik here to view.

Article 20

hi all. well above is a machined cylinder set for the na. i made them in two halves which i will solder together. I used a 1mm cutter on the cnc. for scale the outside of the cylinders are 1/8" diametre.

View Article


Image may be NSFW.
Clik here to view.

Article 19

hi all. just a few more pics. the workshop is a bit full at the moment so have been working on the computer. the na i have changed, it now has a split chassie and solid drivers. both the na and the...

View Article

Image may be NSFW.
Clik here to view.

cab

hi all, a few more recent pics. the white parts are cnc machined styrene. the 3rd pic i hadn't trimed the windows.

View Article

Image may be NSFW.
Clik here to view.

Article 17

hi all, a few more recent shots of the Na. the last photo shows the motor in the background.the chassis is free rolling at this point. This design is far neater than the earlier one, assembly is...

View Article


Image may be NSFW.
Clik here to view.

Article 16

something else in the works,a hon30 version of below. just a rough drawing to see the suitability of off the shelf motors and gearboxes.

View Article


Image may be NSFW.
Clik here to view.

Article 15

latest revision of a hon30 NA loco.

View Article

Image may be NSFW.
Clik here to view.

Article 14

hi all, i have reworked the design of the rods and cranks to improve the assembly. the centre photo shows the jigs to press the wheels onto the axle muffs.

View Article

Image may be NSFW.
Clik here to view.

Article 13

a few more images so far, the cylinders need to redone as there isn't enough clearence for the rods. i will increase the spacing by 0.7 mm from the centreline.

View Article

Image may be NSFW.
Clik here to view.

Article 12

i finished the drive to the spur gear. runs well. I was a bit worried that the reduction on the g15 motor was going to bo to slow, but it looks ok to me. sorry the video is a bit blurry.

View Article


Image may be NSFW.
Clik here to view.

Article 11

Hi all, i have reworked the shaft. There is another support and a universal joint. Its hard to see but these are uni joints supplied by hollywood foundry. The mechinism still needs a good run in. need...

View Article

Image may be NSFW.
Clik here to view.

Article 10

not much added to the NA but i have had a go at some trackwork. the points are 5mm gauge.there made by hand using code 40 micro-engineering rail and nn3 pcb sleepers from fast tracks.

View Article


Image may be NSFW.
Clik here to view.

Article 9

hi all, been a while i know. here are a few recent pics. the new boiler section i have made is out of styrene. i will reproduce this in whitemetal. two reasons for this. i need the weight and i have...

View Article

Image may be NSFW.
Clik here to view.

Article 8

hi all, well i had a go at casting the boiler/side tanks. they turned out quite good. plenty of weight. the truck is a model tt truck, it is by micron art, http://www.micronart.com/index.html

View Article


Image may be NSFW.
Clik here to view.

Article 7

hi all, a few more images. its starting to look like a NA now. the chimney was turned on my lathe,as was the air compressor. handrails and pipes are various sizes of brass wire. the filler caps (i...

View Article

Image may be NSFW.
Clik here to view.

Article 6

hi all, more pics. this is the first coat of paint. is just so i can put the glazing in and glue on the roof.

View Article

Image may be NSFW.
Clik here to view.

Article 5

hi all, i have been doing some drawings lately. I have found some better motors and gears. This will improve running.there both 12v and allow room for a flywheel. The garratt drawing is new, it is...

View Article

Image may be NSFW.
Clik here to view.

Article 4

hello all,a long time i know, anyhow i have started to remake the new design,i have a number of parts i have been making in the next few post.first picture is the wheels, i turned these in one...

View Article


Image may be NSFW.
Clik here to view.

Article 3

gears were cut from mod 64 gears stock, this is available from small parts and bearings.

View Article


Image may be NSFW.
Clik here to view.

Article 2

parts here were cut using a wire cutter edm machine, the advantage of these machines is that the wire is quite fine, allowing very fine corners.shown are the cylinder with valve chest, as well as the...

View Article

Image may be NSFW.
Clik here to view.

Article 1

just the cad render showing the support for the worm shaft.

View Article

Image may be NSFW.
Clik here to view.

Article 0

i took a picture of the lathe tool i used to cut the wheels, the tool has two tip cut on it, the tip on the left can cut the front profile of the wheel, the grooving tool can be used to cut the inner...

View Article

Browsing latest articles
Browse All 25 View Live